Building Science Series, Issues 21-35 |
From inside the book
Results 1-5 of 100
Page 6
... Determine the sump center lines by using the average length and width of the sump . Place the three micrometer dial gages ... determined 10 min after remo al of the applied load is not to exceed 0.008 i ( 2 ) Test Data The relationship ...
... Determine the sump center lines by using the average length and width of the sump . Place the three micrometer dial gages ... determined 10 min after remo al of the applied load is not to exceed 0.008 i ( 2 ) Test Data The relationship ...
Page 9
... determined by per- formance requirements for the static load test ( sec . 2.2 ) . In addition , lateral movement and ... determine if the bathtub will withstand , without visible damage , an impact load simulating a person falling or ...
... determined by per- formance requirements for the static load test ( sec . 2.2 ) . In addition , lateral movement and ... determine if the bathtub will withstand , without visible damage , an impact load simulating a person falling or ...
Page 13
... determined with 0.001 in deflectometer and the no - permanent- deflection requirement was withdrawn . In addi- tion ... determining the presence of any relatively large permanent indentations , or denting , the use of the surface in ...
... determined with 0.001 in deflectometer and the no - permanent- deflection requirement was withdrawn . In addi- tion ... determining the presence of any relatively large permanent indentations , or denting , the use of the surface in ...
Page 16
... determined by t method are entered in table 2.6-1 as the " zero- set . " The zero - offset data are considered to be a proximate because of the curvature of some n ment - deflection curves . ( 3 ) Rationale for Test Selection The ...
... determined by t method are entered in table 2.6-1 as the " zero- set . " The zero - offset data are considered to be a proximate because of the curvature of some n ment - deflection curves . ( 3 ) Rationale for Test Selection The ...
Page 17
... determined by the inspection procedure prescribed in section 2.8 . ( 2 ) Rationale for Suggested Format A limit of ... determining the water- tight - joint potential of bathtubs and no test method is recomemnded . It would seem ...
... determined by the inspection procedure prescribed in section 2.8 . ( 2 ) Rationale for Suggested Format A limit of ... determining the water- tight - joint potential of bathtubs and no test method is recomemnded . It would seem ...
Other editions - View all
Common terms and phrases
applied asphalt ASTM axial load bathtub block brick Building Science Series Bureau of Standards cents Chromel coating color retention Column loads components compressive strength computed construction coordination cracking deg F developed dimensional Dolomite eccentricity effect enamels exposure failure fixture flexural floor load versus Fly Ash FRPE gloss high-bond horizontal industry Kure Beach load versus beam load versus translation louver Major floor load masonry materials maximum measured ment midspan mixer mixing device modular module mortar National Bureau Output Channel percent performance plumbing fixtures Porcelain Enamels Portland Cement precoordination Prestressed Concrete prestressing prisms resistance resistance thermometer shear shear strength shown in figure slab south wind load specifications specimens steel surface temperature tensile strength test results test structure thermistors thermocouples tion vane versus beam deflection VERTICAL DEFLECTION vertical load walls west wind load wind load versus
Popular passages
Page 127 - ABSTRACT (A 200-word or less factual summary of most significant information. If document includes a significant...
Page 6 - In no case does such identification imply recommendation or endorsement by the National Bureau of Standards , nor does it imply that the...
Page 11 - FOR COMPUTER SCIENCES AND TECHNOLOGY conducts research and provides technical services designed to aid Government agencies in improving cost effectiveness in the conduct of their programs through the selection, acquisition, and effective utilization of automatic data processing equipment; and serves as the principal focus...
Page 3 - This report gives findings and recommendations developed during an investigation of performance characteristics for sanitary plumbing fixtures, conducted at the request of the Building Research Advisory Board of the National Academy of Sciences-National Research Council. The...